Truck Bed Upgrade on Oconee Ranger District, Georgia

*see attachments — Statement of Work (SOW) — 2026 Chevrolet 3500 HD (Single Rear Wheel) — OEM Bed Removal and Installation of CM Truck Bed – Model 8'6/84/54/42 — 1. Vehicle Information — • Make/Model: 2026 Chevrolet 3500 HD — • Configuration: Single Rear Wheel — • Current Condition: Equipped with factory‑installed OEM pickup bed and back up camera on factory installed bed — • VIN: 1GC4KSEY1TF291258 — 2. Contractor Responsibilities — The contractor shall perform the following: — A. Removal of Factory Bed — • Safely disconnect all electrical, back up camera, sensors, fuel filler, and auxiliary connections tied to the OEM pickup bed. — • Remove factory bed without damage to the truck frame, chassis wiring, or components. — • Inspect and clean mounting points on the frame after bed removal. — B. Preparation for Upfit — • Verify chassis measurements and mounting compatibility for CM model 8'6/84/54/42. — • Ensure all wiring harnesses, lighting connectors, and fuel filler components are positioned for proper integration with the new bed. — • Provide any necessary mounting hardware if not included by the manufacturer. — C. Installation of CM Truck Bed (Model 8'6/84/54/42) — • Properly mount and secure the CM bed to manufacturer specifications and torque requirements. — • Align and install fuel filler neck, rear lighting, license plate lighting, and reverse sensors (if applicable). — • Connect and test all electrical systems including brake lights, turn signals, reverse lights, and marker lights. — • Ensure the bed sits level, securely fastened, and free of vibration or interference with vehicle components. — D. Quality Check and Testing — • Perform full inspection confirming structural security, proper alignment, and correct electrical function. — • Test vehicle lighting and safety systems to ensure compliance with DOT requirements. — • Verify proper clearance between bed, tires, frame, and suspension components. — 3. Deliverables — • Completed removal of OEM bed — • Fully installed CM Truck Bed (Model 8'6/84/54/42) — • Documentation of all work performed — 4 . Schedule — • Work to begin on: 8/1/26 — • Estimated completion: 8-12 weeks — 5. Acceptance Criteria — The installation will be considered complete when: — • CM bed is mounted to manufacturer specifications — • All electrical and safety systems function correctly — • No fault codes or warning indicators are present — • Vehicle passes final inspection by the government/agency representative — 6. Additional Requirements — • Contractor must follow all safety protocols and industry standards. — • Any changes, unexpected issues, or additional parts required must be approved before proceeding.

*see attachments — Statement of Work (SOW) — 2026 Chevrolet 3500 HD (Single Rear Wheel) — OEM Bed Removal and Installation of CM Truck Bed – Model 8'6/84/54/42 — 1. Vehicle Information — • Make/Model: 2026 Chevrolet 3500 HD — • Configuration: Single Rear Wheel — • Current Condition: Equipped with factory‑installed OEM pickup bed and back up camera on factory installed bed — • VIN: 1GC4KSEY1TF291258 — 2. Contractor Responsibilities — The contractor shall perform the following: — A. Removal of Factory Bed — • Safely disconnect all electrical, back up camera, sensors, fuel filler, and auxiliary connections tied to the OEM pickup bed. — • Remove factory bed without damage to the truck frame, chassis wiring, or components. — • Inspect and clean mounting points on the frame after bed removal. — B. Preparation for Upfit — • Verify chassis measurements and mounting compatibility for CM model 8'6/84/54/42. — • Ensure all wiring harnesses, lighting connectors, and fuel filler components are positioned for proper integration with the new bed. — • Provide any necessary mounting hardware if not included by the manufacturer. — C. Installation of CM Truck Bed (Model 8'6/84/54/42) — • Properly mount and secure the CM bed to manufacturer specifications and torque requirements. — • Align and install fuel filler neck, rear lighting, license plate lighting, and reverse sensors (if applicable). — • Connect and test all electrical systems including brake lights, turn signals, reverse lights, and marker lights. — • Ensure the bed sits level, securely fastened, and free of vibration or interference with vehicle components. — D. Quality Check and Testing — • Perform full inspection confirming structural security, proper alignment, and correct electrical function. — • Test vehicle lighting and safety systems to ensure compliance with DOT requirements. — • Verify proper clearance between bed, tires, frame, and suspension components. — 3. Deliverables — • Completed removal of OEM bed — • Fully installed CM Truck Bed (Model 8'6/84/54/42) — • Documentation of all work performed — 4 . Schedule — • Work to begin on: 8/1/26 — • Estimated completion: 8-12 weeks — 5. Acceptance Criteria — The installation will be considered complete when: — • CM bed is mounted to manufacturer specifications — • All electrical and safety systems function correctly — • No fault codes or warning indicators are present — • Vehicle passes final inspection by the government/agency representative — 6. Additional Requirements — • Contractor must follow all safety protocols and industry standards. — • Any changes, unexpected issues, or additional parts required must be approved before proceeding.